Car On-board diagnostic system

Renault CAN CLIP V172 ISO Software Free Download

Publié le 6/11/2017 à 04:48, MONTMARTE
Mots clefs : Renault CAN ClipRenault ClipRenault CAN Clip V712
(11/06/2017) Renault CAN Clip v172 Multilingual diagnostic software download on Mega:!xdJymSTT!ynCiyBCxpGjFWVsdPdeWBg
Renault CAN Clip – the latest diagnostic tool for vehicles of Renault. It contains all the latest diagnostic technology and information base to address all requirements.
– O.S.: Windows XP, Windows Vista, Windows 7, Windows 8, Windows 8.1, Windows 10
– CPU: Intel/AMD 2 GHz or higher
– RAM: 1 GB of system memory
– Hard Drive: 5 GB of available space
– Optical Drive: DVD-ROM
(Because to use the other option, (renault net), you need to have the renault server/account for reprogramming)
– Required Hardware: Renault CAN Clip Diagnostic Interface
– Files included:
– Security: Unknown
Note: The software is not from me. I hold no responsibility of a bad use.
You can use the last version- Renault CAN CLiP 171 software with security.
CANCLIP V171 is tested by professionals and users many many times. You can use that with relief.
Now, obdii365 experts are testing Renault CLIP 172 for you all. The result will be reported here.
Note: when you try to update Renault CLIP software (for clone tool) and it asks you for device serial number, you can put numbers from 1 to 7… or all zeros…
Renault CAN CLiP update issues & solutions:

Issue: CAN CLIP firmware update at 20% (solutions)

Here are some customer solutions of Renault CAN CLIP firmware update stops at 20%, some solved by files rename and some by CLIP pcb reword.
Solution I: (said 100% working)
For those who have a Chinese Can clip that remain stuck at 20% on the update of the firmware here is the procedure to stop the worries and can again use the Clip device.
Must rename the following files:
C: \ CLIP \ DATA \ APPLI \ PARAMS \ appliiso.s19 in appliiso.bak
C: \ CLIP \ DATA \ APPLI \ PARAMS \ applican.s19 in applican.bak
tested by my self work 100%
Solution II:
if firmware update stops at 20% the solution is very easy
Exist some problems in hardware … ISO pcb or CAN pcb
For bypass that error search for 2 files APLIISO.S19 and APLIICAN.S19 and rename this files to .bak one time ISO …start the soft and ceck …. and one time CAN and restrt the soft and ceck…and you see where is the problem CAN hardware or ISO hardware….
The files is located here :
If you have renamed the right file no more firmware stop at 20% but the problem on hardware remain and is possible use the interface only for ISO or only for CAN vehicles…..or put the interface in trash !!!!
BUT, some say the exactly reasons for 20% update problem is not the software problem! It’s HARDWARE problem with your clone CLIP sonde. You probably have bad flash chip or bad soldering, or bad oscillator, or, … you name it, but anyway as I said it’s pure hardware problem. You can avoid firmware update for ISO or CAN board with renaming few files, but that is not solution because if you can’t update firmware, your CLIP will not work properly. 
Solution III:
Besides two pcb’s inside Clip (can and iso) there is small thrid pcb where is round connector for car cable . When this cable is plugged and unplugged to Clip very often ( which needs a little force ), then solderings on metal pins which links this small pcb with rest of clip are breaking with the time.
You just need to resolder connections of these pins.
I did it and it solve update 20% problem
Renault CAN CLiP reprogramming FAQs:
Q: Why to choose reprogramming through a cd-rom?
A: Because to use the other option, (renault net), you need to have the renault server/account…
Q: What is the purpose of renault can clip reprogramming?
A: This update installs an updated version of the ECU software, it can be released for example, if renault found a glitch in the previous versions, or to make slightly changes as the engine gets older etc…
Q: Do you know if you can reprogram a Renault ECU for more than 1 times???
A: With clip, if the software available is higher than the one installed, you can… You can’t install a lower/older version…

Q: What’s the Renault can clip programming mode serial

A: Renault clip on programming: It asked for a 7-digit serial (digits 0-9).
123456789 works good
all Zeros 0000000
1234567 works fine
Note: with Renault Can Clip china clone, you need luck to do ECU programming and key programming. But most have no luck to do this. You’ll get what you pay for. The Clone are much more cheaper than the Genuine. Usually, CANCLIP interface clone is good at basic OBD2 diagnostic tests and ECU reprogramming only.

Renault CAN CLIP Yellow PCB Support Programming

Publié le 27/07/2017 à 06:03, Marne-la-Vallée
Mots clefs : Renault CAN ClipRenault Clip
Renault CAN CLIP programming tool, where to buy? Renault CAN CLIP yellow pcb version from now is verified to program ECUs and add keys to Renault.
Renault CAN CLIP programming solution:
best quality with AN2135SC AN2136SC full chip








This is the only Renault CAN CLIP china clone (with YELLOW boards) working with PROGRAMMING.
For old versions with GREEN boards. There is NO CHANCE!!!
So, FOGET IT if renault can clip programming
A GOOD TIP: Renault clip on programming asked for a 7-digit serial (digits 0-9).

(solved) Renault CLIP asks for 7 digit serial when programming

When I try to enter programming mode, the Renault CAN CLIP asks for a 7-digit serial (digits 0-9). How to do?
– I put two zeros in front to make it seven digit and it worked.
– My serial is 6 digit long and i put “0” in front of the serial. Worked fine!
– I had the same problem with my clip on programming. It asked for a 7-digit serial (digits 0-9). On my clip there was a sticker with only a 5 digit S/N so I typed in the 5 numbers and added 2 zeros on the end and it accepted them and allowed me to program.
What’s the serial numbers for fully programming, especially programming new or used ecm and also sometimes write injector serials numbers into ecm, for diesel cars…
– 123456789 works good
– 1234567 works fine for me
– On mine is all Zeros 0000000

How to solve Renault CAN Clip Probe Update Failure error

Publié le 4/07/2017 à 04:42, Marne-la-Vallée
Mots clefs : Renault CAN ClipRenault CAN Clip V168Renault Clip


When I using the Renault CAN CLIP diagnostic interface with V156 software, it gave me error:

"Getting in connection 
Download the application firmware. 
Update of the sensor firmware "

Translated in English:

Application firmware download.
Updating the probe firmware”


Failed reservation probe.

Try again and getting technical assistance in case of novel failure.

(Failed to reserve the probe.

Try again and then contract technical assistance in case of novel failure.)



For renault can clip diagnostic interface from China with item no. Sp19-asp19-bsp19-csp19-d

Users have to go to update before using the new software

Select Update, then DO NOT operate the computer


CLIP update is available once

CANNOT cancel the update; if so, the update will be available again only replace a chip marked with red or send back to the factory for repair


Renault can clip diagnostic tools with the newest software from wont pop up the update information.


Now, the newest version is Renault can clip v168:


The message is only popped up when old tools are used with previous Renault CLIP software. For example, a user bought the Renault can clip v160 but now he wanna used it with the latest CLIP v168; then the message above will be displayed.


So, for use of new software, users must update Renault CLIP diagnostic software.

Mes albums

Où suis-je actuellement ?


Mes amis

Sites favoris