Car On-board diagnostic system

Program Nissan Rogue 2010 Key without PIN code

Publié le 9/02/2018 à 09:16, Marne-la-Vallée
Mots clefs : Lonsdor K518Londsor K518ISELonsdor K518 key programmer
Lonsdor K518ISE key programmer was used to program immobilizer key for a Nissan Rogue year 2010, I found extra menu and a few new options, BCM to pin was done automatically.  No need to pic converter, no token, easy instructions. More options for smart key then other programmers.
 
Connect K518ISE host with vehicle via OBD diagnostic socket
Select Immobilizer->Nissan->Select from type->Immobilizer->Electronic Key (E0)->Add key
lonsdor-k518-nissan-rogue-1
lonsdor-k518-nissan-rogue-2
lonsdor-k518-nissan-rogue-3
lonsdor-k518-nissan-rogue-4
lonsdor-k518-nissan-rogue-5
 
 
 
 
 
Insert working key to turn ignition on
lonsdor-k518-nissan-rogue-6
 
Lonsdor K518ISE automatically read BCM code and PIN
lonsdor-k518-nissan-rogue-7
 
Insert new key and turn ignition on
Turn ignition off
Repeat IGN ON/OFF for twice
Program success.
Follow Lonsdor K518 prompt to program next key. Very easy.
lonsdor-k518-nissan-rogue-8
 
I also added smart key on an imported Nissan and other models, no need for hazard light to be on.. Over all experience with Nissan was good.

How to Program Jaguar XJ Smart Key with Lonsdor K518

Publié le 5/01/2018 à 09:06, Aéroport de Paris - Roissy Charles-de-Gaulle
Mots clefs : Lonsdor K518Lonsdor K518ISELonsdor K518 key programmer
Lonsdor K518ISE key programmer has successfully programmed a smart key on a Jaguar XJ. Pictures and procedures attached below.
 
Guide:
Connect K518 host with vehicle via OBD socket
Turn ignition on
Select Immobilizer->Jaguar->XJ->Smart key->Add smart key
lonsdor-k518ise-jaguar-xj-1
 
lonsdor-k518ise-jaguar-xj-2
 
lonsdor-k518ise-jaguar-xj-3
 
lonsdor-k518ise-jaguar-xj-4

communicating
Turn ignition off
Lonsdor K518 Read vehicle VIN,part number,software version
lonsdor-k518ise-jaguar-xj-5
lonsdor-k518ise-jaguar-xj-6
lonsdor-k518ise-jaguar-xj-7
 
 
 
Identify number of keys programmed in car:2
lonsdor-k518ise-jaguar-xj-8

Press OK to program a new smart key
lonsdor-k518ise-jaguar-xj-9

Keep the smart key to be programmed in hand
lonsdor-k518ise-jaguar-xj-10

Programming, press the Unlock button of the smart key once within 5 sec
lonsdor-k518ise-jaguar-xj-11
 
lonsdor-k518ise-jaguar-xj-12
 
A new smart key has been programmed
lonsdor-k518ise-jaguar-xj-13
 
Programming completed
lonsdor-k518ise-jaguar-xj-14
 
Test the new smart key
lonsdor-k518ise-jaguar-xj-15
 
Success!!!

Which Tool is Best for BMW FEM BDC Key Programming?

Publié le 30/10/2017 à 09:22, Aéroport de Paris - Roissy Charles-de-Gaulle
Mots clefs : Lonsdor K518ISELonsdor K518CGDI Prog BMWVVDI2 BMWYanhua BMW FEM

Lonsdor K518ISE, CGDI Prog BMW, Xhorse VVDI2, Yanhua BMW FEM/BDC key programmer all are verified to program FEM/BDC key without issues. But which tool is best for BMW FEM BDC key programming?

 

Look here and you’ll know all:

bmw-fem-bdc-key-programmer

Lonsdor K518ISE program BMW FEM BDC key

CGDI Prog BMW OBD program FEM key

Xhorse VVDI2 BMW do coding/programming to FEM BDC

Yanhua BMW FEM key programmer add a new key

 

lonsdor-k518ise-fem-bdc-key-programmer

1 How to use Lonsdor K518ISE to program BMW FEM BDC key?

 

Three steps: read key info–>pre-process FEM/BDC system–>make a dealer key

In details…

 

Step 1: read key info

MUST read key information first

 

Step 2: pre-process FEM/BDC system

MUST DISCONNECT THE BATTERY

 

1: OBD back up original coding data:

On the car or test platform, connect to FEM/BDC system, then back up original back up coding files via OBD

2: read out EEPROM backup data & generate a service-mode EEPROM:

-> Disassemble FEM/BDC module, find out chip 95128 or 95256, read EEPROM data using a ECU programming tool: VVDI-Prog, Orange5 and the like;

-> Copy the EEPROM data into to the Lonsdor K518ISE customfile folder;

-> Run the program, read original EEPROM data and generate a service-mode EEPROM, upload data of the service-mode EEPROM, write it into chip 95128 or 95256 with help of a ECU programmer

-> Restore FEM/BDC system, supply battery to the car and connect via OBD

Lonsdor-K518ISE-program-BMW-FEM-BDC-key-1

3: programming

-> This step need to be done on the BMW FEM/BDC test platform;

-> Make sure that Step 1 & 2 is finished

-> Connect FEM/BDC system to power supply and connect to the OBD port

 

4: restore EEPROM data

-> disassemble FEM/BDC module, write original EEPROM data (Step 2) into chip 95128/95256

-> restore FEM/BDC system, connect to OBD

 

5: restore coding data

-> load the backup coding files (Step 1), restore coding information via OBD

 

6: pre-processing is complete.

 

Step 3: make a dealer key

 

1: Lonsdor K518ISE read out data, select the will-be key position

2: a “used”key to make a dealer key

All keys lost: enter 32bit ISN codes to make a dealer key

3: put the key near the car immo induction loop

Lonsdor-K518ISE-program-BMW-FEM-BDC-key-2

4: detect the original key, read out immo data

5: put a new key near the car immo induction loop

6: detect the key key, key learn (don’t move the key, keep stable)

7: key learn is complete

 

Step 4: disable the key

 

1: Lonsdor K518ISE read out data, select the key ID position to disable

2: put a “used” key near the car induction loop

3: K518ISE system tries to connect to CAS, disable the key with current ID position, disable key successfully

 

Step 5: enable the key

 

1: Lonsdor K518ISE read out data, select the key ID position to enable

2: put a “used” key near the car induction loop

3: K518ISE system tries to connect to CAS, enable the key with current ID position, enable key successfully

 

Step 6: delete the key

 

1: K518ISE read out data, select the key ID position to delete

2: read FEM/BDC key password

3: delete the key successfully; the key position is blank

 

THE MOST IMPOERTAN TIPS

1: You must read key info before everything you’ll do

2: to pre-process FEM/BDC, you should pay attention to:

– backup coding codes to continue

– disconnect to the power supply/battery, have a ECU programmer to read EEPROM data, up load data in K518 customfile folder, read new EEPROM data loaded just now, generate service-mode EEPROM data, read service-mode EEPROM data, write data into the chip, install CPU on the car

– ECU programming: need 6 min, with power supply connected

– disconnect to the power supply, disassemble CPU, write the original EEPROM data into the chip, install CPU on the car, connect to the power supply, make sure communicate is successful

– upload coding files (Step 1), restore original coding info to pre-process, then make a dealer key

3: 32bit ISN codes is required to program a new key when ALL KEYS ARE LOST

 

Job’s done with Lonsdor K518ISE!

 

cgdi-prog-fem-bdc-key-programmer-bmw

2 How to use CGDI Prog BMW to OBD program FEM key

 

Go to BMW OBD Key Match

CGDI-BMW-FEM-program (1)

The current FEM/BDC needs to update the ECU program before performing key matching. Please ensure that the car battery has enough power, the programming process, please keep the equipment cable connection

CGDI-BMW-FEM-program (2)

Please remove the FEM/BDC and then use the CGDI Prog programmer to read and save data from the P5XXX EEPROM chip on the FEM/BDC computer board, then click on Next

CGDI-BMW-FEM-program (3)

Read the original car EEPROM data file

CGDI-BMW-FEM-program (4)

CGDI-BMW-FEM-program (5)

CGDI-BMW-FEM-program (6)

Use the CGDI Prog BMW to write the calculated new data to the 95XXX EEPROM chip, then put the FEM/BDC back into the car, thn click on Next

CGDI-BMW-FEM-program (7)

Car battery voltage: 11.93V

Prepare the programming ECU

Security authentication is in process

Safety certification through

The ECU is being programmed

CGDI-BMW-FEM-program (8)

Please remove the FEM/BDC and then use the CGDI Prog programmer to read and save data from the P5XXX EEPROM chip on the FEM/BDC computer board, then click on Next

CGDI-BMW-FEM-program (9)

Setting code

Coding is successful

CGDI-BMW-FEM-program (10)

CGDI-BMW-FEM-program (11)

FEM/BDC key matching need to enter engine ISN, please select the way of input ISN code

CGDI-BMW-FEM-program (12)

OBD is connecting

OBD KWP-CAN 500kbps connection is successful

CGDI-BMW-FEM-program (13)

Loading the code data file

CGDI-BMW-FEM-program (14)

CGDI-BMW-FEM-program (15)

CGDI-BMW-FEM-program (16)

Coding is successful

 

xhorse-vvdi2-bmw-fem-bdc-program

3 Xhorse VVDI2 BMW FEM/BDC coding/programming 

 

 

BMW FEM/BDC Coding/Programming with VVDI2 full kit 4.3.0 above

vvdi2-bmw-fem-programming-2

step 1:

  1. read FEM/BDC coding via OBDII or on the bench
  2. you’d better not close this window after starting this procedure

 

step 2:

  1. open FEM/BDC shell, find out where the 95128/95256 chip is, read EEPROM dump via BDM programmer
  2. load original EEPROM dump and save special EEPROM dump, write special EEPROM dump back to the 95128/95256 chip
  3. restore FEM/BDC shell, provide -12v and connect it via OBD

 

step 3:

  1. this operation requires connecting FEM/BDC on the bench, and make sure you finish step 1 ans step 2
  2. provide +12v to FEM.BDC and connect it via OBD

 

step 4:

  1. open FEM/BDC shell, write original EEPROM dump (read step 2) back to the 95128/95256 chip
  2. restore FEM/BDC shell and connect it via OBD

 

step 5:

loading coding file (read step 1), write to FEM/BDC via OBDII, finish FEM/BDC programming

 

 

Attention please!!!

– You can directly backup/restore coding

– You have to pre-setup the FEM/BDC module before deleting/adding keys or resetting keys

– You’ll be told other tools need to be used first to program the FEM/BDC system, then setup FEM/BDC via VVDI2. It happens when you do FEM/BDC key learning, and you don’t have a working software version

– You’d better not close the VVDI2 interface when you pre-setup FEM/BDC

– You need do with 95128(FEM) or 95256(BDC) chip when pre-setup FEM/BDC

Note: there are two 8-pin chips; do not disassemble the wrong chip; better refer to the wiring diagram

– You must restore original EEPROM data, restore coding when pre-setup FEM/BDC. If you fail to restore coding or the remote cannot start or something wrong with the window (or other failures probably) after coding restore and FEM/BDC installation, please use other tools to do re-coding FEM/BDC

– Ask tech support @obdii365 for help, if the replay sounds continuously after supplying power to the FEM/BDC. Usually, it needs programming.

 

yh-bmw-fem-key-programmer

Yanhua BMW FEM key programmer add a new key

 

There are 5 steps for you to have Yanhua BMW FEM/BDC programmer add/program a new key.

 

Step 1: backup (read) coding data

Step 2: update/program ECU

Step 3: program/learn (add) key

Step 4: restore (write) coding data

Step 5: delete keys disabled

 

How to Program BMW FEM key with Yanhua BMW FEM/BDC programmer

 

In summary,

all tools above (Lonsdor K518ISE, CGDI BMW, VVDI2, Yanhua BMW FEM/BDC key programmer) can work good in FEM/BDC programming. So, Lonsdor K518ISE vs CGDI BMW vs Xhorse VVDI2 vs Yanhua tool, which best for OBD program BMW FEM/BDC? it depends on your budget and future use.

 

For BMW only: CGDI Prog BMW or Yanhua BMW FEM/BDC key programmer

For VAG+BMW: Xhorse VVDI2 is the best solution.

For universal key programming: Lonsdor K518ISE key programming machine never fails.

 

CGDI BMW price: us$629

Yanhua FEM/BDC programmer price: US$529

Lonsdor K518ISE price: US$1199

Xhorse VVDI2 BMW: US$1029

 

http://blog.obdii365.com/2017/10/30/program-bmw-fem-key-by-vvdi2-k518-cgdi-or-yanhua-fem/

Ferrari 458 Remote Key Programming with Lonsdor K518

Publié le 21/10/2017 à 08:25, Paris - Charles-de-Gaulle
Mots clefs : Lonsdor K518Lonsdor K518ISELonsdor K518ISE key programmer

Lonsdor K518ISE key programmer is able to program remote key on Ferrari 458, F12 and F149 currently. Here’s the guide on programming Ferrari 458 remote with K518.

Procedure:

Step 1: Backup immo data

Step 2: Program key

Step 3: Program remote

Step 1: Backup Immo Data
Connect K518ISE host with vehicle via diagnostic socket
Select Immobilzation->Ferrari->458->Immobilizer->
lonsdor-k518ise-ferrari-1
lonsdor-k518ise-ferrari-2
lonsdor-k518ise-ferrari-3
Select Backup Immo Data function
lonsdor-k518ise-ferrari-4
Turn ignition ON
Communicating
K518ISE will show hardware and software information
lonsdor-k518ise-ferrari-5
Turn ignition OFF
Reading immo data, wait for 6 minutes
lonsdor-k518ise-ferrari-6
Lonsdor K518ISE will read Ferrari 458 pin code and key security data after 6 minutes
write down the pin code
lonsdor-k518ise-ferrari-7
save immo data as bin format
lonsdor-k518ise-ferrari-8
Backup success
lonsdor-k518ise-ferrari-9
Step 2: Program Key

 

Select Program Key function
lonsdor-k518ise-ferrari-10
The original working key also need to program.
New key to program must be a customized or a pre-written key
lonsdor-k518ise-ferrari-11
Turn ignition ON
Lonsdor K518 then will require to enter PIN code to access
Enter 5-digit pin code and confirm
lonsdor-k518ise-ferrari-12
Number of keys programmed: 1
Press YES to program next key or press NO to go back
lonsdor-k518ise-ferrari-13
Program key complete
lonsdor-k518ise-ferrari-14
Step 3: Program Remote
Select Program Remote function
lonsdor-k518ise-ferrari-15
Turn ignition ON
Again enter PIN code here
lonsdor-k518ise-ferrari-16
Hold remote key to be programmed in hand
Click OK
Click on remote control for 3 sec within 15 sec
press any button on remote key for 3 sec
lonsdor-k518ise-ferrari-17
lonsdor-k518ise-ferrari-18
Number of remote control programmed: 1
Press YES to program next remote
lonsdor-k518ise-ferrari-19
Program remote complete.
lonsdor-k518ise-ferrari-20

 

http://lonsdor-k518ise.blogspot.com/

 

Lonsdor K518 Program Smart key for Volvo V60

Publié le 16/10/2017 à 09:24, Paris - Charles-de-Gaulle
Mots clefs : Lonsdor K518Lonsdor K518ISE
Lonsdor K518ISE (same company made SKP1000) has wide key programming vehicle coverage , especially Volvo (S40, S60, S80, XC60, XC90, C30, C70, V40, V60, V70).  Here’s demo guide on programming V60 smart key with K518.
 
Step 1:Read the CEM security data
Volvo’s CEM is basically located behind the storage box which is in front of the co-pilot seat
Dismantle & read CEM to backup security data
volvo-v60-cem-1
volvo-v60-cem-2
 
 
Connection between Lonsdor K518ISE host, adapter and RN-01 board :
lonsdor-k518-v60-1
 
Read Volvo CEM please use RN-01 adapter.
Read CEM data and save it as VOV.BIN
 
Step 2: Program Smart Key
Reinstall CEM back to vehicle
Connect Lonsdor K518 host with vehicle via OBD socket
Select IMMOBILIZATION->VOLVO->Add a key
You can also program all keys lost if lost all keys
lonsdor-k518-v60-2
 
K518 ask to upload CEM data just read
lonsdor-k518-v60-3
 
lonsdor-k518-v60-4
 
Select and update CEM data VOV.BIN
Press on Start button
Follow K518 prompt then it will show you current key programmed: 2
lonsdor-k518-v60-7
 
Insert new key to be programmed into card slot
lonsdor-k518-v60-8
 
Follow K518 prompt to complete
Key programmed: 3
lonsdor-k518-v60-9
 
Program success.
lonsdor-k518-v60-10
 
Program smart key complete, remote will automatically generated
Test the new remote.
http://www.skp1000.org/program-volvo-v60-smart-key-with-lonsdor-k518/

Mes albums

Où suis-je actuellement ?



Rubriques

Mes amis

Sites favoris