Car On-board diagnostic system

How to add Cummins Inline5 to INSITE 8.2.0 software

Publié le 22/12/2017 à 08:38, Aéroport de Paris - Roissy Charles-de-Gaulle
Mots clefs : Cummins Iniste 8.2.0Cummins Insite 8.2.0.184Cummins Inline 5Cummins Inline 6

Here’s the instruction on adding Cummins Inline 5 data link truck diagnostic adapter to INSITE 8.2.0 software.

 

 

Preparation:

First you need to close all anti-virus software program

Then install Cummins 8.2.0 pro/lite version software

How to Install Activate Cummins Insite 8.2.0.184 Pro and Lite

 

Step 1: Install Inline 5 driver 

 

Check your operating system, here we set it up on Windows 7 32-bit

use-inline5-with-insite-820-1

Open software CD

Open INSITE.7_6_2.rar-> Software folder->INSITE 5 Drivers

use-inline5-with-insite-820-2

use-inline5-with-insite-820-3

Copy Inline 5.7.0.1 Setup- 32 Bit.exe to desktop

If you use 64-bit system, you copy Inline 5.7.0.1 Setup- 64 Bit.exe to desktop

use-inline5-with-insite-820-4

Install the adapter driver, here we use Cummins Inline5 data link (you can use Inline 6, nexiq or other adapters as well)

Run Inline 5.7.0.1 Setup-32 Bit on desktop as administrator 

use-inline5-with-insite-820-5

Click on NEXT

use-inline5-with-insite-820-6

Accept the windows security warning to install driver software

use-inline5-with-insite-820-7

Tick “Launch Inline 4/5 Reflash Tool” and click on Finish

Delete Inline 5.7.0.1 Setup-32 Bit on desktop

Device driver has been successfully installed

use-inline5-with-insite-820-8

use-inline5-with-insite-820-9

Open Computer->Manager->Device Manager->Universal Serial Bus Controller to check device is well connected

use-inline5-with-insite-820-10

Step 2: Add Inline5 adapter to INSITE 8.2.0

 

Open INSITE 8.2.0.184 pro or lite version software on desktop

use-inline5-with-insite-820-11

Select Add New option on the middle of the bottom tool bar

use-inline5-with-insite-820-12

Click Next to install ECU Connection Wizard

use-inline5-with-insite-820-13

Select RP1210 adapters, click on Next

use-inline5-with-insite-820-14

Select Vendor, Adapter INLINR 5 USB and protocol Auto detect, click on Next

use-inline5-with-insite-820-15

Click on Next

use-inline5-with-insite-820-16

Tick both 2 options and click Finish

Again software will prompt to install ECU connection wizard, click next

Do the same setting as above, but this time we choose protocol J1708

use-inline5-with-insite-820-17

Click Finish

Do the setting again, this time we add protocol J1939

use-inline5-with-insite-820-18

Click Finish and cancel ECU connection wizard interface

use-inline5-with-insite-820-19

Please add the corresponding adapter in the iniste software

use-inline5-with-insite-820-20

Select INLINES USB (Auto Detect) Connection on the middle of bottom tool bar

use-inline5-with-insite-820-21

Click Connect button to connect to ECM

Now you can using the software, read fault code, manage data logger, do calibration etc

use-inline5-with-insite-820-22

use-inline5-with-insite-820-23

use-inline5-with-insite-820-24

www.obdii365.com

http://blog.obdii365.com/2017/12/21/use-cummins-insite-8-2-0-184-with-inline5-data-link/


Mes albums

Où suis-je actuellement ?



Rubriques

Mes amis

Sites favoris